Photos

This spring pushes the detent in locking it in place when you release the lever.

This spring pushes the detent in locking it in place when you release the lever.

  • Reaction score 0
  • Comments 0
Hi-Low pinion block.

Hi-Low pinion block.

  • Reaction score 0
  • Comments 0
This is how the adjustable detent plate goes together. View 3 set screw going in to hold the adjustable plate in place.

This is how the adjustable detent plate goes together. View 3 set screw going in to hold the adjustable plate in place.

  • Reaction score 0
  • Comments 0
How the adjustable detent plate goes together. View 2 The set screw end.

How the adjustable detent plate goes together. View 2 The set screw end.

  • Reaction score 0
  • Comments 0
how the adjustable detent plate goes together. View 1.

how the adjustable detent plate goes together. View 1.

  • Reaction score 0
  • Comments 0
This detent plate is adjustable using the set screw you see in the upper right hand corner.

This detent plate is adjustable using the set screw you see in the upper right hand corner.

  • Reaction score 0
  • Comments 0
High-low shift lever assembly.

High-low shift lever assembly.

  • Reaction score 0
  • Comments 0
Tighten the clamps (from the previous picture) until the faces of the Bull gear and the Pinion gear are aligned.

Tighten the clamps (from the previous picture) until the faces of the Bull gear and the Pinion gear are aligned.

  • Reaction score 0
  • Comments 0
Next you need to clamp down the bull gear. This is to align the gear faces of the bull gear and the pinion gear.

Next you need to clamp down the bull gear. This is to align the gear faces of the bull gear and the pinion gear.

  • Reaction score 0
  • Comments 0
View inside housing where Set screw "A" leads to.

View inside housing where Set screw "A" leads to.

  • Reaction score 0
  • Comments 0
Infamous screw "A"... unscrew this set screw and fill with super lube.

Infamous screw "A"... unscrew this set screw and fill with super lube.

  • Reaction score 0
  • Comments 0
Brass guides installed overhead view.

Brass guides installed overhead view.

  • Reaction score 0
  • Comments 0
Brass guides installed side view.

Brass guides installed side view.

  • Reaction score 0
  • Comments 0
Install the brass guides here as shown to align the bull gear assembly.

Install the brass guides here as shown to align the bull gear assembly.

  • Reaction score 0
  • Comments 0
Brass guides that align the bull gear sleeve/assembly on the gear housing.

Brass guides that align the bull gear sleeve/assembly on the gear housing.

  • Reaction score 0
  • Comments 0
After sliding the bull gear assembly into place.

After sliding the bull gear assembly into place.

  • Reaction score 0
  • Comments 0
Installing the bull gear bearing sleeve. slide in through the large washer on the 3 springs you just installed.

Installing the bull gear bearing sleeve. slide in through the large washer on the 3 springs you just installed.

  • Reaction score 0
  • Comments 0
Lubed bull gear bearing sleeve.

Lubed bull gear bearing sleeve.

  • Reaction score 0
  • Comments 0
Lubricate the bull gear bearing sleeve using super lube or something close.

Lubricate the bull gear bearing sleeve using super lube or something close.

  • Reaction score 0
  • Comments 0
Place the washer over the springs like shown.

Place the washer over the springs like shown.

  • Reaction score 0
  • Comments 0
3 springs install...with my installer hand out of the way. lol

3 springs install...with my installer hand out of the way. lol

  • Reaction score 0
  • Comments 0
Install the 3 compression springs into their pockets in the gear housing. (clean and lightly lubricate.)

Install the 3 compression springs into their pockets in the gear housing. (clean and lightly lubricate.)

  • Reaction score 0
  • Comments 0
Compression springs that help the control of the bull gear movement (up and down) when shifting between High and Low speeds.

Compression springs that help the control of the bull gear movement (up and down) when shifting between High and Low speeds.

  • Reaction score 0
  • Comments 0
Side profile I cut on the lock nut socket "teeth" using a dremel with a cutoff wheel. Straight on view if you look to the back tooth.

Side profile I cut on the lock nut socket "teeth" using a dremel with a cutoff wheel. Straight on view if you look to the back tooth.

  • Reaction score 0
  • Comments 0
Back
Top