Photos

Slide the worm gear on to the shaft. Line up the drilled holes in the shaft with the ones on the gear. :)

Slide the worm gear on to the shaft. Line up the drilled holes in the shaft with the ones on the gear. :)

  • Reaction score 0
  • Comments 0
Start rebuild. After everything is cleaned up. Lightly oil the speed change shaft before inserting into the housing.

Start rebuild. After everything is cleaned up. Lightly oil the speed change shaft before inserting into the housing.

  • Reaction score 0
  • Comments 0
Speed change hub still installed in the bearing block...angled view.

Speed change hub still installed in the bearing block...angled view.

  • Reaction score 0
  • Comments 0
Speed change hub cleaned up...still in bearing block.

Speed change hub cleaned up...still in bearing block.

  • Reaction score 0
  • Comments 0
Speed change hub showing the chain attached with a roll pin

Speed change hub showing the chain attached with a roll pin

  • Reaction score 0
  • Comments 0
Speed change hub with chain attached.

Speed change hub with chain attached.

  • Reaction score 0
  • Comments 0
Back face of speed change gear cleaned up.

Back face of speed change gear cleaned up.

  • Reaction score 0
  • Comments 0
Front face of speed change gear cleaned up.

Front face of speed change gear cleaned up.

  • Reaction score 0
  • Comments 0
Speed change housing showing the the speed Over-limit stop.

Speed change housing showing the the speed Over-limit stop.

  • Reaction score 0
  • Comments 0
Speed change housing showing the front.

Speed change housing showing the front.

  • Reaction score 0
  • Comments 0
Speed change housing showing the bronze bearing where the shaft goes.

Speed change housing showing the bronze bearing where the shaft goes.

  • Reaction score 0
  • Comments 0
Speed change housing with worm gear and shaft removed.

Speed change housing with worm gear and shaft removed.

  • Reaction score 0
  • Comments 0
Picture of speed change shaft assembly with new shaft.

Picture of speed change shaft assembly with new shaft.

  • Reaction score 0
  • Comments 0
Use a punch to remove the pin. This will allow you to remove the shaft...but don't unless you have to!

Use a punch to remove the pin. This will allow you to remove the shaft...but don't unless you have to!

  • Reaction score 0
  • Comments 0
Plastic bearing block with hub still installed...gear removed.

Plastic bearing block with hub still installed...gear removed.

  • Reaction score 0
  • Comments 0
This pin connects the gear to the hub. It goes in a hole that's drilled in it..

This pin connects the gear to the hub. It goes in a hole that's drilled in it..

  • Reaction score 0
  • Comments 0
Back side of gear removed....

Back side of gear removed....

  • Reaction score 0
  • Comments 0
Front side of gear removed....

Front side of gear removed....

  • Reaction score 0
  • Comments 0
The gear should come off without too much trouble. Although you may need to pry a little bit.

The gear should come off without too much trouble. Although you may need to pry a little bit.

  • Reaction score 0
  • Comments 0
There is a wavy spring washer between the speed change handle and the speed change housing. Don't lose it!

There is a wavy spring washer between the speed change handle and the speed change housing. Don't lose it!

  • Reaction score 0
  • Comments 0
Remove the speed change handle. It's secured with this set screw.

Remove the speed change handle. It's secured with this set screw.

  • Reaction score 0
  • Comments 0
Speed change assembly, rear view of bearing block showing the gear.

Speed change assembly, rear view of bearing block showing the gear.

  • Reaction score 0
  • Comments 0
Speed change assembly, rear view of bearing block showing the gear.

Speed change assembly, rear view of bearing block showing the gear.

  • Reaction score 0
  • Comments 0
Speed change bearing block assembly, speed dial and mounting screws.

Speed change bearing block assembly, speed dial and mounting screws.

  • Reaction score 0
  • Comments 0
Back
Top