Photos

20170529_124035

20170529_124035

  • Reaction score 0
  • Comments 0
Tighten the 3 cap screws down and you've installed the bearing cap. Next!

Tighten the 3 cap screws down and you've installed the bearing cap. Next!

  • Reaction score 0
  • Comments 0
Another view of where you install the bearing cap screws.

Another view of where you install the bearing cap screws.

  • Reaction score 0
  • Comments 0
Install the 3 cap head scres like so. The other three holes in the cap are used for removing a stuck cap.

Install the 3 cap head scres like so. The other three holes in the cap are used for removing a stuck cap.

  • Reaction score 0
  • Comments 0
I had put witness marks when I removed the bearing cap. If you did make sure to line them up.

I had put witness marks when I removed the bearing cap. If you did make sure to line them up.

  • Reaction score 0
  • Comments 0
Place the bearing cap over the bearing and the wavy spring washer.

Place the bearing cap over the bearing and the wavy spring washer.

  • Reaction score 0
  • Comments 0
Set the wavy spring washer on top of the bearing.

Set the wavy spring washer on top of the bearing.

  • Reaction score 0
  • Comments 0
Side view of wavy spring washer...new wavy spring washer.

Side view of wavy spring washer...new wavy spring washer.

  • Reaction score 0
  • Comments 0
Next up bearing cap installation. You'll need what you see here. Bearing cap, 3 cap screws, and the wavy spring washer...

Next up bearing cap installation. You'll need what you see here. Bearing cap, 3 cap screws, and the wavy spring washer...

  • Reaction score 0
  • Comments 0
Another top down view of the speed plate screws showing the space around the pivot sleeve.

Another top down view of the speed plate screws showing the space around the pivot sleeve.

  • Reaction score 0
  • Comments 0
How it'll look after you install the speed change plate screws with pivot sleeves. They will have space around them.

How it'll look after you install the speed change plate screws with pivot sleeves. They will have space around them.

  • Reaction score 0
  • Comments 0
Here you can see the speed change plate holes lined up with the sliding bearing housing.

Here you can see the speed change plate holes lined up with the sliding bearing housing.

  • Reaction score 0
  • Comments 0
Use these two screws with the pivot sleeves to mount the speed change plate to the sliding bearing housing.

Use these two screws with the pivot sleeves to mount the speed change plate to the sliding bearing housing.

  • Reaction score 0
  • Comments 0
The other two shorter cap screws go here. This will mount the upper belt housing to the lower belt housing. Only a few more steps to go!

The other two shorter cap screws go here. This will mount the upper belt housing to the lower belt housing. Only a few more steps to go!

  • Reaction score 0
  • Comments 0
The two long cap head screws go here.

The two long cap head screws go here.

  • Reaction score 0
  • Comments 0
These are the 4 cap screws you'll use to attach the upper belt housing to the lower belt housing.

These are the 4 cap screws you'll use to attach the upper belt housing to the lower belt housing.

  • Reaction score 0
  • Comments 0
Just in case you forgot we are going to take this rebuilt upper belt housing...flip it over and place it on top of the Lower belt housing.

Just in case you forgot we are going to take this rebuilt upper belt housing...flip it over and place it on top of the Lower belt housing.

  • Reaction score 0
  • Comments 0
Use the other 2 cap screws here to finish securing the lower belt housing to the heaad unit. These are on the front.

Use the other 2 cap screws here to finish securing the lower belt housing to the heaad unit. These are on the front.

  • Reaction score 0
  • Comments 0
Use 2 of the cap screws here. These two holes are in the back.

Use 2 of the cap screws here. These two holes are in the back.

  • Reaction score 0
  • Comments 0
The four cap screws you will need to mount the lower belt housing to the head unit.

The four cap screws you will need to mount the lower belt housing to the head unit.

  • Reaction score 0
  • Comments 0
Roughly the position the lower belt housing will be before you attach it next.

Roughly the position the lower belt housing will be before you attach it next.

  • Reaction score 0
  • Comments 0
Another view of how the timing belt is installed. Looking down through the lower belt housing.

Another view of how the timing belt is installed. Looking down through the lower belt housing.

  • Reaction score 0
  • Comments 0
At this point you are going to wish you had three hands.

At this point you are going to wish you had three hands.

  • Reaction score 0
  • Comments 1
This is the top of the gear housing showing the timing pulley. Put your new timing belt on now like shown.

This is the top of the gear housing showing the timing pulley. Put your new timing belt on now like shown.

  • Reaction score 0
  • Comments 0
Back
Top