I have a no. 12 van norman for sale and a customer asked what year it is. As per the normal information using the google on the internet machine there is a page that lists serial number info. It suggests the ser # should read 12-XXXX but also in the fine print it says there are some machines that were marked differently. My machine is marked with a 13XXX format . I did see some posts on a few sites that came up from the search saying they had similar numbers and their "books" recognized this number format. Does anyone have any information other than what is online?
-
Welcome back Guest! Did you know you can mentor other members here at H-M? If not, please check out our Relaunch of Hobby Machinist Mentoring Program!
No. 12 Van normal serial numbers.
- Thread starter jamie76x
- Start date
- Joined
- Sep 3, 2011
- Messages
- 478
I've never heard of a 13XXX serial number on a Van Norman No. 12. The serial number is stamped on the front surface of the vertical flat way for the knee, at the top. Sometimes it's 12-XXXX, sometimes it's XXXX-12, and sometimes it's just XXXX. XXXX should be between 5000 and 9999. Apparently in 1954 they ran out of serial numbers and added another digit, i.e. 10000, but I don't think they got to 13000. Can you post a photo of the machine?
Cal
The machine is a no 12, Its right in the casting. The numbers are in the normal spot on the top right hand side of the way, the numbers just don't make make sence. I have run into a hand full of these machines before and all had the normal number format. I have read about other machines with the same 5 digit number, but can not find info on how to tell how old it is.
- Joined
- Sep 3, 2011
- Messages
- 478
whatever.
Don't get pissy Cal...... You replied to my post with the same exact information that I provided in the original post. Sorry you can't be the hero on this post.
If anyone has any information other than what is in the original post, then please share.
If anyone has any information other than what is in the original post, then please share.
- Joined
- Sep 22, 2010
- Messages
- 7,224
Easy fellas....Cal is one of the most knowledgeable people around on this mill.
The best written source I know for the numbers is Jim Kasunich's site:
http://jmkasunich.com/vannorman/VN_Serial.htm
From Jim's site:
The model number and serial number of a Van Norman mill are usually stamped in the front face of the column, at the top. For example, my mill is stamped "12-5751". The "12" means that it is a model #12 mill. The "5751" is the serial number. If I run down the #12 column of the table, I see that the last mill made in 1940 was number 5443, and the last one made in 1941 was 5903. Since 5751 is between those two numbers, I know that my mill was made somewhere around the middle of 1941. Not all mills use the same format for the serial numbers - an owner of an older #12 has informed me that his mill is marked 5074-12, (serial number first, then model number). It is possible that some mills don't include the model number at all, or that they have additional digits before or after the serial number to specify options, etc.
Another very knowledgeable source is Repair Parts Inc.
http://www.repair-parts-inc.com/
Could you post a photo of the serial number? They appear all over the machine including the tool tray, ram bed, etc.
Last edited by a moderator:
- Joined
- May 17, 2012
- Messages
- 105
I'm back after a long absence. I just picked up a Van Norman No. 12 mill with no motor and I've run into the same serial number issue Jamie76X had. My serial number is clearly a 13 series number.
I picked it up for scrap value with free delivery. It has a lovely brush paint job, mostly on the previously painted areas of the machine. The electrical cabinet contains equipment that will work on 60, 50, and 25 hz. The drive motor for the table is still present and is 3 phase, 60hz.
I have two .pdfs of the operating and parts manuals that have no dates. One shows a pretty art deco styled head with a fairly rectangular access plate, and one shows a blocky head with a T shaped access plate. My mill is the latter style. Does this help in dating the mill?
I received a number of collets and two arbors, and the round overarm bar, but no arbor support. This is where I see another difference from the manuals. Both show cuts in the face of the spindle for drive keys, and mine does not have these. I notice that the collets (Hardinge !) have slots for a key and the spindle has a slot for a key. Is it normal to put a square key in the slot? This is more for curiosity at this point, as I'm a long way out from running the machine.
It sat for 30 years unused in the back of a garage knifemaking shop, and is absolutely filthy. When turned by hand, the gears and bearings feel fine, but there are issues with the saddle moving. It is extremely stiff.
I picked it up for scrap value with free delivery. It has a lovely brush paint job, mostly on the previously painted areas of the machine. The electrical cabinet contains equipment that will work on 60, 50, and 25 hz. The drive motor for the table is still present and is 3 phase, 60hz.
I have two .pdfs of the operating and parts manuals that have no dates. One shows a pretty art deco styled head with a fairly rectangular access plate, and one shows a blocky head with a T shaped access plate. My mill is the latter style. Does this help in dating the mill?
I received a number of collets and two arbors, and the round overarm bar, but no arbor support. This is where I see another difference from the manuals. Both show cuts in the face of the spindle for drive keys, and mine does not have these. I notice that the collets (Hardinge !) have slots for a key and the spindle has a slot for a key. Is it normal to put a square key in the slot? This is more for curiosity at this point, as I'm a long way out from running the machine.
It sat for 30 years unused in the back of a garage knifemaking shop, and is absolutely filthy. When turned by hand, the gears and bearings feel fine, but there are issues with the saddle moving. It is extremely stiff.
Attachments
Can you post photos of the differences you noted and of the mill generally?
A 5-digit serial number is probably a later machine, but your description of the head suggests maybe not, as the blocky head with a T-shaped plate preceded the football-shaped head design.
The spindle should have a filed-down Woodruff key in it (there's a drawing in the Files section here showing the dimensions), that's normal and expected for the VN C collet system. I still need to make one for my mill too. Additionally, the spindle should have two square-ish drive dogs on either side of it also, for driving horizontal arbors, shell mills, etc.
A 5-digit serial number is probably a later machine, but your description of the head suggests maybe not, as the blocky head with a T-shaped plate preceded the football-shaped head design.
The spindle should have a filed-down Woodruff key in it (there's a drawing in the Files section here showing the dimensions), that's normal and expected for the VN C collet system. I still need to make one for my mill too. Additionally, the spindle should have two square-ish drive dogs on either side of it also, for driving horizontal arbors, shell mills, etc.