Derbyshire Magnus rehab

When I read the name of the thread, I thought that old Magnus from Derbyshire fell off the wagon again!

Great job.

Richard

Derbyshire Magnus rehab​

 
I went to a swapmeet this morning. I found 2 small 3 jaw chucks. I never see small chucks 2” or so. Anyhow scooped them up for $6 each. One is a craftsman with 1/2”-20 threads. The other is a made in India with a 12 mm thread.
The craftsman is a bit heavy I think. The India one is better suited. The craftsman runs smooth. As for the India it is unused and sticky. It will need a tear down and good cleaning. I will see if I can find the D style collet adapter for them. Worst case is I can modify the supplied MT2 on the India one. The pain will be making a Buttress threading tool for 10mm.
feeb70c7441d0590a481acaa377079e9.jpg



Cutting oil is my blood.
 
Last edited:
Interesting find on the India chuck. The jaws are reversible. Swap jaws 1&3 when flipping.
d24bcd28f971efeab62ca2181e7372cb.jpg

81824109a6dbd5376d37391009dd6f2e.jpg



Cutting oil is my blood.
 
I started making a riser today. It is made from a 3” dia x 3” long piece of CRS.

To do the radial cut for the lathe bar to fit. I just took my 1-1/2” fly cutter and extended the cutter out to make a 1-3/4” dia.

06063dd04bb6ad2bb60f07ccba263e24.jpg

260e517d34390fb1d077d51f16383110.jpg

a695a114615f18963a8825380929dc50.jpg

4de5902806a5b297d598a893fe607fed.jpg

e5cb2ee71424dc717032963ace1952f5.jpg



I need to drill and tap 2 mounting holes on the bottom to mount to a board eventually.


Cutting oil is my blood.
 
Just painted it. I also picked up a piece of pine for the base. I will mess with that next week as I have next week off.
55c649e35a565d7e83c1cf9548535537.jpg

d1d2449cd04a1ab646fdb057723e41ad.jpg



Cutting oil is my blood.
 
Double post fixed.
 
Last edited:
I got 3 hours in today. I was able to get pretty far on the tool rest. All I need to do on the flipper is drill and ream a hole for the tool rest holder. The pivot is reamed .126 through one end of the base and flipper. The other end is reamed .125.

Tomorrow I will do that and make the holder se toon for the tool rest and the tool rest.
0d19ceb4c73198881de679e82f8903de.jpg

8d7be3481be21b37084da6f4c9bc61ac.jpg

b35f8cd4f364fae63ee48f77bcb20d81.jpg

f509e8ededc85a4e6a959db14235b1fc.jpg

fc69370741560d9a4c52493a5bf598b3.jpg

96accbaa38c46e7e22dd9582d2f9c18d.jpg

fe88c459c4161cc3cf1cdcdc4da6f1cd.jpg



Cutting oil is my blood.
 
Last edited:
Got another 1-1/2 in today. I have it all finished up except getting a thumb screw to secure the toolpost. I also need to make a knob to secure the entire holder down to the bed.
2efd0b640ac98aa7e21cfc6142e6ab99.jpg

8ac91361d5c3a18a556f2acb1fc49d6c.jpg

f9a239760657805357300a2cd061df17.jpg

00728a06d5bc17bd47659514153c90bf.jpg



Cutting oil is my blood.
 
Back
Top