Photos

Navigation

  1. Member Photos 248
  2. H-M Video Library 2
    1. Commercial & Sponsor Video Channels 2
Browse albums

Trending media

20170410_161442

20170410_161442

  • Media owner Randy803
  • Date added Apr 10, 2017
  • Reaction score 0
  • Comments 0
20170410_161402

20170410_161402

  • Media owner Randy803
  • Date added Apr 10, 2017
  • Reaction score 0
  • Comments 0
20170410_161314

20170410_161314

  • Media owner Randy803
  • Date added Apr 10, 2017
  • Reaction score 0
  • Comments 0
Last thing to do is slide a collet in and out of the spindle to insure it doesn't bind up. Then install the hollow locking set screw to lock it.

Last thing to do is slide a collet in and out of the spindle to insure it doesn't bind up. Then install the hollow locking set screw to lock it.

  • Reaction score 0
  • Comments 0
Install the 1st set screw. Normally at this point you put in a R8 collet to insure you don't go to deep with the set screw. I didn't have one handy.

Install the 1st set screw. Normally at this point you put in a R8 collet to insure you don't go to deep with the set screw. I didn't have one handy.

  • Reaction score 0
  • Comments 0
Last thing on the list is installing the R8 collet alignment screw. It's a double set screw as shown.

Last thing on the list is installing the R8 collet alignment screw. It's a double set screw as shown.

  • Reaction score 0
  • Comments 0
Bend the tab into place with a screw driver and the mallet.

Bend the tab into place with a screw driver and the mallet.

  • Reaction score 0
  • Comments 0
When you finish tightening the spindle lock nut stop where you can line up one of the tabs with a slot on the nut.

When you finish tightening the spindle lock nut stop where you can line up one of the tabs with a slot on the nut.

  • Reaction score 0
  • Comments 0
Get the spanner wrench! Tighten the nut down a couple of light taps with the dead blow. Don't over tighten or you will bind the bearings.

Get the spanner wrench! Tighten the nut down a couple of light taps with the dead blow. Don't over tighten or you will bind the bearings.

  • Reaction score 0
  • Comments 0
Mount the spindle in the vise (with soft jaws or covered in brass like mine.) Bearings on the right side this time.

Mount the spindle in the vise (with soft jaws or covered in brass like mine.) Bearings on the right side this time.

  • Reaction score 0
  • Comments 0
Time to install the spindle lock nut. Start screwing it on then mount it in the vise with soft jaws. This time bearings on the right side.

Time to install the spindle lock nut. Start screwing it on then mount it in the vise with soft jaws. This time bearings on the right side.

  • Reaction score 0
  • Comments 0
Spindle lock washer install line up the tab with the keyway slot.

Spindle lock washer install line up the tab with the keyway slot.

  • Reaction score 0
  • Comments 0
Spindle lock washer view 2. Showing tab.

Spindle lock washer view 2. Showing tab.

  • Reaction score 0
  • Comments 0
Spindle lock washer view 1.

Spindle lock washer view 1.

  • Reaction score 0
  • Comments 0
The slot you align the lock spindle lock washer with.

The slot you align the lock spindle lock washer with.

  • Reaction score 0
  • Comments 0
New top bearing in place.

New top bearing in place.

  • Reaction score 0
  • Comments 0
Install the top bearing. Install the side of the bearing that has the Thicker inner race towards the spacer.

Install the top bearing. Install the side of the bearing that has the Thicker inner race towards the spacer.

  • Reaction score 0
  • Comments 0
Make sure the top spindle bearing spacer is clean and install it.

Make sure the top spindle bearing spacer is clean and install it.

  • Reaction score 0
  • Comments 0
Lower bearing set installed! Good job almost done!

Lower bearing set installed! Good job almost done!

  • Reaction score 0
  • Comments 0
Press the 2nd bearing in place. Keeping your marks aligned with the v's on the both bearings.

Press the 2nd bearing in place. Keeping your marks aligned with the v's on the both bearings.

  • Reaction score 0
  • Comments 0
Keep your marks lined up!

Keep your marks lined up!

  • Reaction score 0
  • Comments 0
Installing the spacers view one

Installing the spacers view one

  • Reaction score 0
  • Comments 0
Installing the spacers view two.

Installing the spacers view two.

  • Reaction score 0
  • Comments 0
Lube everything and slide the spacers into place. Line up the marks that you placed on the spacer with the V on the bearing.

Lube everything and slide the spacers into place. Line up the marks that you placed on the spacer with the V on the bearing.

  • Reaction score 0
  • Comments 0
Back
Top