Photos

IMG_1659

IMG_1659

  • Media owner Poppey
  • Date added Jul 21, 2017
  • Reaction score 0
  • Comments 0
Us}anon7

Us}anon7

  • Media owner Desolus
  • Date added Jul 21, 2017
  • Reaction score 0
  • Comments 0
The plate in it's home another shot from the end of the garage.

The plate in it's home another shot from the end of the garage.

  • Reaction score 0
  • Comments 0
The plate made it to it's new home!

The plate made it to it's new home!

  • Reaction score 0
  • Comments 0
Now to remove the rails just lift the plate via the 3 mounting points until you can see light between the rails and the plate.

Now to remove the rails just lift the plate via the 3 mounting points until you can see light between the rails and the plate.

  • Reaction score 0
  • Comments 0
At this point the plate is still sitting on the slide rails.

At this point the plate is still sitting on the slide rails.

  • Reaction score 0
  • Comments 0
The plate made it! The last couple of inches I had to remove the bike hanger and pulley. Then push it the rest of the way. Which was easy.

The plate made it! The last couple of inches I had to remove the bike hanger and pulley. Then push it the rest of the way. Which was easy.

  • Reaction score 0
  • Comments 0
The particular setup was 1 to 1 on leverage so It didn't work just pulling on the rope.

The particular setup was 1 to 1 on leverage so It didn't work just pulling on the rope.

  • Reaction score 0
  • Comments 0
The plate didn't slide easy...so I thought I'd attach a pulley to the bench. I used a single pulley and a bike hanger. Screw in type.

The plate didn't slide easy...so I thought I'd attach a pulley to the bench. I used a single pulley and a bike hanger. Screw in type.

  • Reaction score 0
  • Comments 0
Starting to slide it down the rail was the hardest part. As the plate went from flat to sloped. A little more lifting than I wanted.

Starting to slide it down the rail was the hardest part. As the plate went from flat to sloped. A little more lifting than I wanted.

  • Reaction score 0
  • Comments 0
A close up of the factory installed mount pads. Had to make sure these didn't get pryed off while sliding it down the rail.

A close up of the factory installed mount pads. Had to make sure these didn't get pryed off while sliding it down the rail.

  • Reaction score 0
  • Comments 0
There are mounting pads on the bottom of the plate. These had to fit between the rails. I had to keep adjusting as I slid it.

There are mounting pads on the bottom of the plate. These had to fit between the rails. I had to keep adjusting as I slid it.

  • Reaction score 0
  • Comments 0
Another view of the rails on the stand. The mounting screws are turned down below the level of the sideways 2x4s

Another view of the rails on the stand. The mounting screws are turned down below the level of the sideways 2x4s

  • Reaction score 0
  • Comments 0
A view of how the rail looked attached to the ledge on the pallet.

A view of how the rail looked attached to the ledge on the pallet.

  • Reaction score 0
  • Comments 0
I placed a single support under the center. I made sure that the 2x4s were directly supporting the load.

I placed a single support under the center. I made sure that the 2x4s were directly supporting the load.

  • Reaction score 0
  • Comments 0
I made sure the rails were as wide as the stand. Which I made an inch wider than the plate for room to move. So it needed a couple of 25" spacers.

I made sure the rails were as wide as the stand. Which I made an inch wider than the plate for room to move. So it needed a couple of 25" spacers.

  • Reaction score 0
  • Comments 0
There was a slight slope from the truck to the stand. Roughly 6" of drop. These are the rails I attached to the ledge I put on the stand.

There was a slight slope from the truck to the stand. Roughly 6" of drop. These are the rails I attached to the ledge I put on the stand.

  • Reaction score 0
  • Comments 0
I added a ledge for the rails to sit on directly to the shipping pallet the surface plate was on.

I added a ledge for the rails to sit on directly to the shipping pallet the surface plate was on.

  • Reaction score 0
  • Comments 0
This is where I got the idea of where I could put rails to slide it on. So it needed a cleat. See next pictures

This is where I got the idea of where I could put rails to slide it on. So it needed a cleat. See next pictures

  • Reaction score 0
  • Comments 0
Just another angle of the garage from where I was moving the plate...

Just another angle of the garage from where I was moving the plate...

  • Reaction score 0
  • Comments 0
I had the plate on it's shipping pallet... plus One more pallet that I had in the warehouse.

I had the plate on it's shipping pallet... plus One more pallet that I had in the warehouse.

  • Reaction score 0
  • Comments 0
What I had to do.

What I had to do.

  • Reaction score 0
  • Comments 0
Media 2016-11-03, 3-18 PM-1

Media 2016-11-03, 3-18 PM-1

  • Media owner CT129guy
  • Date added Jul 15, 2017
  • Reaction score 0
  • Comments 0
Media 2016-11-03, 3-18 PM

Media 2016-11-03, 3-18 PM

  • Media owner CT129guy
  • Date added Jul 15, 2017
  • Reaction score 0
  • Comments 0
Back
Top