Photos

Install the large nuts on the left. Both of them go on the left.

Install the large nuts on the left. Both of them go on the left.

  • Reaction score 0
  • Comments 0
The large nuts go on the Left side of the unit as you face it.

The large nuts go on the Left side of the unit as you face it.

  • Reaction score 0
  • Comments 0
Once you have the head in place the bolts should stick out about this much.

Once you have the head in place the bolts should stick out about this much.

  • Reaction score 0
  • Comments 0
The head is in place! Time to put the washers and nuts on the bolts.

The head is in place! Time to put the washers and nuts on the bolts.

  • Reaction score 0
  • Comments 0
My table was tilted and the ram was adjusted to match the tilt. So have a 3/4" wrench ready to make adjustments.

My table was tilted and the ram was adjusted to match the tilt. So have a 3/4" wrench ready to make adjustments.

  • Reaction score 0
  • Comments 0
All 4 bolts in roughly lined up position.

All 4 bolts in roughly lined up position.

  • Reaction score 0
  • Comments 0
This is how the bolts slide around the slot....basic but how they go.

This is how the bolts slide around the slot....basic but how they go.

  • Reaction score 0
  • Comments 0
There is a notch in the ram as shown. The bolts go in this way and are tilted up into position. Then slide them around to approximate location..

There is a notch in the ram as shown. The bolts go in this way and are tilted up into position. Then slide them around to approximate location..

  • Reaction score 0
  • Comments 0
The bolts, washers and nuts needed to install the head. These have square heads.

The bolts, washers and nuts needed to install the head. These have square heads.

  • Reaction score 0
  • Comments 0
Wide view before bringing the head up to the ram. My table stand had a tilt to it. We approach that shortly.

Wide view before bringing the head up to the ram. My table stand had a tilt to it. We approach that shortly.

  • Reaction score 0
  • Comments 0
There are 4 bolt holes to align putting the head back on the mill. There are inserts in there...make sure they stay there!

There are 4 bolt holes to align putting the head back on the mill. There are inserts in there...make sure they stay there!

  • Reaction score 0
  • Comments 0
20170731_143003

20170731_143003

  • Media owner Desolus
  • Date added Jul 31, 2017
  • Reaction score 0
  • Comments 0
IMG_1665

IMG_1665

  • Media owner MSD0
  • Date added Jul 28, 2017
  • Reaction score 0
  • Comments 0
IMG_0173

IMG_0173

  • Media owner Nobby
  • Date added Jul 28, 2017
  • Reaction score 0
  • Comments 0
20170728_143126

20170728_143126

  • Media owner Desolus
  • Date added Jul 28, 2017
  • Reaction score 0
  • Comments 0
DSC03720

DSC03720

  • Reaction score 0
  • Comments 0
G&E1

G&E1

  • Reaction score 0
  • Comments 0
DSC03906

DSC03906

  • Reaction score 0
  • Comments 0
DSC03907

DSC03907

  • Reaction score 1
  • Comments 0
DSC03906

DSC03906

  • Reaction score 0
  • Comments 0
3-ball dynamics

3-ball dynamics

  • Media owner whitmore
  • Date added Jul 24, 2017
  • Reaction score 0
  • Comments 0
IMG_0025

IMG_0025

  • Media owner Poppey
  • Date added Jul 22, 2017
  • Reaction score 0
  • Comments 0
IMG_0020

IMG_0020

  • Media owner Poppey
  • Date added Jul 22, 2017
  • Reaction score 0
  • Comments 0
IMG_0029

IMG_0029

  • Media owner Poppey
  • Date added Jul 22, 2017
  • Reaction score 0
  • Comments 0
Back
Top