Tool Holders? Anybody used these?

I don't know anything about those particular ones however i've purchased both these sets:
www.ebay.com

5× AXA 2# 250-102 Quick Change Tool Post Boring Turning Holder For Lathe 6-12" | eBay

<li> Description:</li> <li>AXA Size Quick Change Tool Post Set for Lathe 6 - 12" 250-102 Boring, Turning Tool Holder, use tool bit up to 1/2" and round shank tool bits up to 7/16" Brand new Suitable for lathe center height 0.6 - 1.75" (top compound surface to lathe center line)...
www.ebay.com

And these:
www.ebay.com

5 Pack AXA #1 250-101 Quick Change Tool Post Turning & Facing Holder For Lathe | eBay

<li> Feature:</li> <li>Brand new Lathe swing: Up to 12" Tool bit capacity: 3/16 - 1/2"</li> <li>Quick and easy to install. Securely holds 3/16 - 1/2" square diameter tool bits. Precision ground and hardened. Completely sealed for maintenance free operation. Maximum rigidity for chatter free...
www.ebay.com

The quality was adequate and they seem to work fine. I have a mix of Phase II, accusize, Aloris and generic import tool holders and they all seem to work fine. I can't make them that cheap for sure - they're under $10 each.
 
rwm said:
That's for a SET OF 4!
Click to expand...
Not sure I understand.... you posted an eBay link that had them for $34.15 for a single piece or four for $28.69 USD per piece, not $28 for four pieces.
My link was for $28 CDN per piece which is $20 USD.
Or did I miss your point?

EDIT: I completely mis-read the listing....
 

Attachments

  • Screenshot 2023-10-10 at 14-58-11 Labwork 4PCS AXA #1 250-101 Quick Change Tool Post Turning F...png
    Screenshot 2023-10-10 at 14-58-11 Labwork 4PCS AXA #1 250-101 Quick Change Tool Post Turning F...png
    17.8 KB · Views: 51
Last edited:
DavidR8 said:
Not sure I understand.... you posted an eBay link that had them for $34.15 for a single piece or four for $28.69 USD per piece, not $28 for four pieces.
My link was for $28 CDN per piece which is $20 USD.
Or did I miss your point?
Click to expand...
If you read the details in the description, 1 pkg means one set of four tool holders. So 4 tool holders for $34.15 USD, or about $8.54 USD per holder. This is a pretty good price.

If you bought 4 pkgs, it would cost $114.76 USD ($28.69 x 4) and you'd get 16 holders, or $7.1725 USD per holder.
 
WobblyHand said:
If you read the details in the description, 1 pkg means one set of four tool holders. So 4 tool holders for $34.15 USD, or about $8.54 USD per holder. This is a pretty good price.

If you bought 4 pkgs, it would cost $114.76 USD ($28.69 x 4) and you'd get 16 holders, or $7.1725 USD per holder.
Click to expand...
Whoops I totally mis-read that. That is a good deal if you're in the US.
 
DavidR8 said:
Whoops I totally mis-read that. That is a good deal if you're in the US.
Click to expand...
Some of the ads are really hard to tell what you are getting. Better to get 1 pkg and receive 4 units, than see the picture of 4 and only get 1!
 
WobblyHand said:
Some of the ads are really hard to tell what you are getting. Better to get 1 pkg and receive 4 units, than see the picture of 4 and only get 1!
Click to expand...
1000%
 
You must log in or register to reply here.
Back
Top